Maintenance

Is It Cheaper to Leave Heating On All Day or Use a Timer?

Is it cheaper to leave the heating on all day or use a timer? What government and Ofgem advice says for a gas or oil boiler, and how the programmer, thermostat and radiator valves fit in.

Illustration of a wall thermostat and timer panel beside a radiator with a coat on a hook

For a normal boiler and radiator system, leaving the heating on low constantly is not more efficient than turning it on and off. The government answers this directly. A home heated when nobody is there wastes energy, and it may be too cold when you actually are there. It is much better to use a programmer or timer so the heating is on when you are home and off when you are not.

Many homeowners and tenants worry about heating bills as winter approaches. You might be staring at your thermostat, wondering if changing the settings will keep the house warmer for less money.

Is it cheaper to leave heating on all day

Many people hear conflicting advice about the best way to run a central heating system. The idea of leaving the heating on low all day is a very common one. People often think that heating a cold house from scratch takes a massive amount of energy, and that keeping it at a steady temperature must be easier on the boiler.

Homes are not perfectly sealed boxes. They lose heat to the outside air through several common areas:

  • The roof and loft space
  • The external walls
  • The windows and doors
  • The gaps around draughty skirting boards

The colder it is outside, the faster the heat escapes from the building. If you leave your heating on all day while you are at work, your boiler has to keep firing to replace the heat that is constantly escaping. You are essentially paying to keep an empty house warm, fighting a continuous battle against the cold weather outside.

With a timer, the heating is off while nobody is home, so you are not paying to heat empty rooms.

When you finally come home and the timer clicks on, the boiler has to work to raise the temperature again. Even so, the government factsheet advises using a programmer or timer rather than leaving the heating on low, and it is general advice rather than a promise about any one home.

What government advice says about constant low heating

For a normal boiler and radiator system, government advice is direct. A government factsheet published in 2016 to help households keep warm for less addresses the myth directly. It asks the specific question of whether constantly leaving the heating on low is more efficient than turning it on and off. The answer given in the factsheet is a definite no.

The factsheet explains that leaving the heating on means your home is heated when you are not there to benefit from it. It also points out a practical problem for your comfort. A constant low setting may leave the house too cold when you are actually at home and want to relax in the evening. The official advice is to use a timer or programmer to ensure the heating is on when you are home and off when you are not.

The energy regulator Ofgem gives similar advice. An Ofgem leaflet focused on saving money and using less energy tells households to use a timer on their central heating system. It advises setting the heating and hot water to come on only when required. This is general advice for homes with a normal boiler and radiators, and it is not a promise about any one home.

What the programmer, room thermostat and radiator valves do

To see how a timer fits in, it helps to know how your heating controls work together. A central heating system relies on several different parts to decide when the boiler fires, how hot the water is and where it flows.

The programmer or timer determines when the heating automatically turns on and off. This is the brain of the schedule. You set the times that match your daily routine. When the programmer is in an off period, the heating is off.

The room thermostat acts as the temperature monitor. It turns the heating off whenever the room goes above the set temperature. This means the boiler is not using energy when the home is warm enough, even if the programmer is in an on period. The government factsheet advises keeping your room thermostat set between 18 degrees Celsius and 21 degrees Celsius.

A crucial fact to remember is that turning the room thermostat up does not make the home warm up more quickly. The thermostat does not change how fast your home heats up, it only acts as a limit. Thermostatic radiator valves are the dials fitted to the side of individual radiators. These control the temperature in different rooms by restricting the flow of hot water into the radiator.

They also allow you to turn the heating off completely in a room that is not in use, such as a spare bedroom. The boiler thermostat controls the temperature of the water the boiler sends to the radiators. It is normally set to high, leaving the room thermostat and the radiator valves to control the actual heating levels in the house.

Here is a summary of what the different controls do.

Heating control

What it does for the system

Programmer or timer

Determines when the heating automatically turns on and off

Room thermostat

Turns the heating off whenever the room goes above the set temperature

Thermostatic radiator valve

Controls the temperature in different rooms or turns off unused rooms

Boiler thermostat

Controls the temperature of the water the boiler sends to the radiators

These descriptions come from the 2016 government factsheet.

How to set a timer around your day

Setting your heating to match your routine is the most practical way to stay warm without wasting fuel. You want the house to be comfortable when you wake up and when you return from work. You do not need the heating running while you are asleep or out of the house.

The government factsheet advises using your timer or programmer to heat your home only at times when you need it. That usually means setting it to come on before you get up and before you arrive home, and off when you are out or in bed.

Check the timer settings against your routine now and then, because a schedule that suited you in summer may not suit you in winter.

The government factsheet says installing and correctly using a full set of heating controls could save you around £80 to £165 a year. This is a 2016 estimate based on a family of four sharing a three-bedroom semi-detached home, not a promised saving for your property.

You might also want to read a central heating winter checklist to help you prepare your radiators and pipes for the colder months.

Hot water and the cylinder

Your heating controls also manage your hot water, and the most efficient way to run this depends entirely on the type of boiler you have. A combi boiler provides hot water directly from the mains without needing a storage tank. On a combi boiler, the hot water is heated as you need it.

If you have a system or regular boiler, you will have a separate hot water cylinder or tank, usually kept in an airing cupboard. If your boiler has a hot water tank, set the hot water to come on around half an hour before you need it in the morning. You must also make sure the tank is well insulated to keep the water hot for longer after the boiler switches off.

Temperature settings are very important for stored hot water for safety reasons. The hot water temperature should be set to 60 degrees Celsius and not lower. This rule exists to prevent the build up of legionella bacteria in the stored water. Ofgem also advises that if you have a hot water tank, you should set the cylinder thermostat to 60 degrees Celsius.

Some hot water tanks have an electric immersion heater. The factsheet advises trying not to use it where possible, because it is more expensive than using the boiler.

Here are the normal hot water settings for different boiler types.

Boiler type

Hot water timing

Temperature rule

Combi boiler

Heated as you need it

Follow the manufacturer's instructions

System or regular boiler

Set to come on half an hour before needed

Cylinder thermostat at 60 degrees Celsius

These settings come from the 2016 government factsheet and the Ofgem leaflet.

When the answer is different

The advice to use a timer applies to normal gas, oil and LPG boilers with standard radiators. However, there are situations where you might need to manage your heating quite differently.

Heat pumps are run differently from boilers. For a heat pump, follow the installer or manufacturer instructions.

Electric storage heaters are also run differently. Again, follow the specific instructions for your storage heaters rather than treating them like a gas boiler.

The insulation of your home also plays a part in how quickly it cools down. Very well insulated homes hold onto their heat for a long time, meaning the temperature drops very slowly when the heating is off. Poorly insulated homes lose heat rapidly and feel cold almost as soon as the radiators cool down.

What a heating engineer can check

If you are using your timer correctly but your home still feels cold, or your bills seem unusually high, a professional can inspect the system. They can make sure your controls are actually communicating with the boiler. A faulty room thermostat or programmer can stop the controls working as they should.

An engineer will check that the programmer is working and that the thermostatic radiator valves are not stuck. A plumber or heating engineer can check whether a valve is stuck and replace it if needed.

During a call out for a cold house, an engineer will usually look for several common issues:

  • That the programmer is sending the correct on and off signals to the boiler
  • That the room thermostat is accurately reading the air temperature
  • That the thermostatic radiator valves are not stuck in the closed position
  • That the boiler thermostat is set high enough to heat the water for the radiators

The most important check is the annual service. According to HSE gas safety advice for homeowners, gas appliances should be serviced at least annually by a Gas Safe registered engineer.

Landlords are legally required to arrange an annual gas safety check and give tenants the record. A service is how a Gas Safe registered engineer checks the boiler.

You can learn more about what happens during a boiler service to understand why this annual check matters. Remember that by law, only Gas Safe registered engineers may work on gas appliances. Do not attempt to remove the boiler casing or adjust internal gas parts yourself, as DIY gas work is illegal.

Common questions

Is it cheaper to leave the heating on all day?

For a normal boiler and radiator system, the government factsheet says leaving the heating on low is not more efficient than turning it on and off. It advises using a programmer or timer so the heating is on when you are home and off when you are not.

Is it cheaper to keep heating on all day?

For a normal gas or oil boiler and radiator system, the factsheet advice is to use a programmer or timer. Heat pumps and electric storage heaters are run differently, so follow the installer or manufacturer instructions, and homes vary, including well insulated ones.

Is it cheaper to leave heating on low all day?

Leaving the heating on low constantly is not more efficient than turning it on and off. If the temperature drops, the boiler still has to fire to maintain that low setting, using energy when nobody is there to benefit. You also risk the house being uncomfortably cold when you want to relax in the evening, as a low setting may not be warm enough.

Is it better to leave heating on low all day?

It is not better for your comfort or your bills. A low constant setting can mean the house is heated when you are out but too cold when you are in. The factsheet advises a room thermostat set between 18 degrees Celsius and 21 degrees Celsius, with a timer or programmer.

Next steps to cut waste without losing comfort

Taking control of your heating system does not mean sitting in a freezing house. It means making sure the boiler only works when it actually needs to. You can easily adjust your setup to match government advice and stop paying for heat you do not feel.

Here are the steps to take with your heating controls:

  • Set your programmer so the heating is on when you are home and off when you are not
  • Check your room thermostat is set between 18 degrees Celsius and 21 degrees Celsius
  • If you have a hot water tank, check its cylinder thermostat is set to 60 degrees Celsius, following the manufacturer's instructions
  • Turn the thermostatic radiator valves down in rooms you rarely use
  • Avoid turning the room thermostat up to heat the house faster
  • Arrange an annual service with a Gas Safe registered engineer

If your controls are broken, or you want to upgrade to a modern programmer, a local heating engineer can help. You can find a plumber near you to check your controls and ensure your boiler is ready for the winter.

Find a top rated plumber near you

4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county:

All counties and towns · The UK Top 100 plumbers

Matt Sutherland
Written by

Matt is a writer and editor for Top Rated Plumbers, covering plumbing, heating and boilers. When he's not writing guides, he spends weekends walking in the Peak District.

Looking for a trusted plumber? Browse our verified listings.

Find a Plumber