Maintenance

Pipe Lagging and Which Pipes to Insulate Before Winter

Which pipes to lag (loft, garage, outside walls, outside tap), what thickness and material to use, what the water regulations say and typical 2026 prices for materials and fitting.

Illustration of lagged pipes in a loft and an insulated outside tap

To protect your home before winter, you should apply pipe lagging to any pipe in an unheated space, such as a loft, garage, basement or outside, and fit an insulated cover over your outside tap. Foam lagging is cheap to buy, with typical 2026 materials costing from £0.50 to £1.50 a metre for standard polyethylene foam. If you prefer to hire a professional, a plumber typically charges £120 to £300 for a fixed-rate pipe lagging job.

What pipe lagging does and does not do

Pipe lagging is a protective layer of foam insulation that wraps around your water pipes. It works by slowing down the rate at which heat escapes from the pipe into the surrounding cold air. By holding onto that ambient heat for longer, the insulation significantly lowers the risk of the water inside freezing solid.

You must remember that lagging does not generate heat of its own. It cannot make a pipe completely immune to frost. If the temperature in your loft or garden stays low enough for a sustained period, water standing still inside an insulated pipe can still freeze.

Water movement plays a large part in preventing ice from forming. Moving water is far harder to freeze than standing water. This is why rarely used fixtures tend to freeze first, while the pipes supplying your main bathroom might stay clear because they are flushed regularly.

Insulation buys you time during a cold snap. It slows the freezing process down enough that normal daily water use keeps the pipes flowing. Once the water stops moving at night, the insulation acts as a barrier against the cold loft air until the morning.

Which pipes to lag first

The rule for preventing winter damage is to insulate any pipework running through an unheated space. These are the areas of your property where temperatures drop fastest and stay low the longest. According to WaterSafe, the national register of approved plumbers, you should look for exposed pipes in these unheated spaces:

  • Lofts and attic spaces
  • Garages and outbuildings
  • Basements and cellars
  • Exposed water supply pipes on external walls
  • The outside tap
  • The boiler condensate pipe

The outside tap itself is highly vulnerable and needs an insulated cover to protect the metal casing and the water sitting just inside the valve. The boiler condensate pipe is the plastic tube that carries waste water from a boiler to a drain. Where it runs outside it is at risk of freezing, and any work on it is a job for a Gas Safe registered engineer.

Prioritise the pipes that are most exposed. How exposed a pipe is, whether it is insulated, how long the cold lasts and whether water is moving through it are the four things that make a difference.

Loft pipes and the cold water tank

Your loft is often the coldest part of the house, leaving the pipes up there entirely exposed to freezing air. You need to lag every accessible section of loft pipework to protect the plumbing system properly. This means covering the vertical risers that bring water up, and the horizontal runs that carry it across the ceiling joists.

You must also insulate the connections leading to the cold water tank or the boiler feed. The joints and corners need careful protection too. You should insulate bends, valves and fittings, using mitred cuts at 45 degrees so the foam fits snugly around corners. Leaving gaps at the joints defeats the purpose of the lagging.

If you have a traditional gravity plumbing system, you will have a cold water storage tank in the loft. Cold water tanks should be insulated to prevent freezing, but their lids must be left vented.

Working in a loft can be difficult due to limited space and poor lighting. If you cannot reach the pipes safely, or if they run under heavy boarding, you should hire a professional to fit the insulation for you.

Outside taps and pipes on outside walls

Outdoor plumbing is the most exposed part of your water system. You should fit an insulated cover on the outside tap before winter arrives. Because the tap is rarely used during the colder months, the water inside sits completely still, making it the first point to freeze when temperatures drop.

Any exposed water supply pipes running along outside walls also need foam insulation.

Despite the clear risk of burst exterior pipes, many homes remain unprotected. WaterSafe's own research found that less than one in four people say they insulate their water pipes to prepare for winter.

In a separate WaterSafe survey of 2,000 UK householders, 23% had experienced a burst or leaking pipe because it froze, and only 33% insulate their outdoor tap. An insulated cover on the outside tap is a small job compared with dealing with a burst pipe. The water company is responsible for the main and the pipe up to the property boundary, but the property owner is responsible for pipes on their land and inside the building.

What thickness and material to buy

Foam insulation is cheap and easy to find in most DIY stores. When choosing your pipe lagging, you need to look at the wall thickness of the foam as well as the diameter of the pipe. A wall thickness of 15mm to 25mm is sufficient for standard pipe sizes in most UK lofts.

If you live in a colder area, you need thicker insulation. A thickness of 25mm to 32mm is often recommended for northern or very exposed lofts. The material your pipes are made from also matters. Plastic pipes lose heat faster than copper pipes, so consider slightly thicker insulation if your home uses plastic plumbing.

The table below shows the typical material costs for different types of pipe insulation.

Material type

Typical 2026 price per metre

Polyethylene foam

£0.50 to £1.50

Rubber nitrile

£2 to £5

Foil-faced

£3 to £6

Phenolic foam

£4 to £8

These are typical 2026 prices, and local prices for materials will differ depending on where you shop.

What the water regulations say about frost

Protecting your plumbing from freezing is covered by law in England and Wales. The Water Supply (Water Fittings) Regulations 1999 are the rules for water fittings. Under Schedule 2 paragraph 4 of the England and Wales version of the regulations, every water fitting must be so constructed and installed as to inhibit damage by freezing or any other cause.

The rules also apply to water storage in the loft. Schedule 2 paragraph 16(4) states that every storage cistern must be fitted with an overflow pipe, a cover that excludes light and insects, and thermal insulation to minimise freezing or undue warming.

Water Regs UK says that it is good practice to insulate both hot and cold water pipework to prevent undue warming of the cold water supply.

Lagging helps protect your property from freezing, but it does not make a pipe frost-proof.

How much pipe lagging costs

A registered plumber can fit insulation for anyone not confident doing it themselves. Professional labour costs £100 to £300 depending on the complexity of the pipework and how easy it is to access your loft. A fixed-rate pipe lagging job typically costs £120 to £300 in total.

When asking for prices, make sure you get a written quote rather than an estimate. A proper written quote should include:

  • A fixed price for the whole job
  • The cost of the foam materials
  • Any call-out fee or minimum charge
  • Whether the total includes VAT

If the plumber or heating engineer works by the hour instead of a fixed price, you can expect a rate of £40 to £70 per hour. You can read more about plumber call-out charges to understand how these fees work.

If you are having a full loft insulation upgrade that includes pipe lagging, the cost ranges from £400 to £1,200. WaterSafe cites the Association of British Insurers as putting the average weather-related home insurance claim for a burst pipe at £9,300.

There is no legal licence for general water plumbing, which is why qualifications and approved schemes matter. WaterSafe is the national register of approved plumbers, with approved contractor schemes run by APHC, CIPHE, SNIPEF and WIAPS. Its members are trained in the Water Fittings Regulations.

Under the Consumer Rights Act 2015, any plumbing service must be carried out with reasonable care and skill. If the insulation is fitted poorly and leaves gaps, you can ask for the poor work to be put right at no extra cost. Services arranged online or at home usually carry a 14-day cooling-off period, but this does not automatically apply to urgent repairs you have asked for.

If you find a frozen pipe while checking your loft, you can read the guide on how to stop your pipes freezing for other frost steps. Never apply a naked flame, a blowtorch or boiling water to a frozen pipe, because rapid heating can split a pipe that is already weak.

If you suspect your home has old asbestos lagging on its pipes, do not disturb it and ask a qualified professional for help.

Common questions

What is foam pipe lagging made from?

Foam pipe lagging can be made from polyethylene foam, which is the lowest priced option in the table above at £0.50 to £1.50 a metre. You can also buy rubber nitrile, foil-faced insulation or phenolic foam for different plumbing situations.

Does outdoor pipe lagging need to be thicker?

Pipes outside are highly exposed to cold air and wind, so they need robust protection to slow down heat loss. A wall thickness of 25mm to 32mm is often recommended for northern or very exposed lofts. For pipes outside the loft, ask a plumber what thickness suits yours. You should always ensure the insulation completely covers the pipe with no gaps at the corners.

How do I measure pipe insulation?

You need to match the internal diameter of the insulation to the outside diameter of your copper or plastic water pipe. You also need to choose the wall thickness of the foam, with 15mm to 25mm being sufficient for standard pipe sizes in most UK lofts. Plastic pipes lose heat faster than copper, so you might consider slightly thicker lagging for a plastic system.

Why do people search for pipe lagging outside?

Many homeowners search for outside lagging because the outside tap and the boiler condensate pipe are at risk of freezing. Despite this risk, less than one in four people insulate their water pipes for winter. Fitting an insulated cover on the outside tap is a quick way to protect it.

What to do next

If you are preparing your home for winter, follow these steps to protect your plumbing system:

  • Check your loft, garage and basement for any exposed pipes.
  • Buy foam insulation and fit it tightly around straight runs.
  • Insulate bends and valves using mitred cuts at 45 degrees.
  • Fit an insulated cover over your outside tap.
  • Ask a Gas Safe registered engineer to deal with the boiler condensate pipe if it runs outside.
  • Hire a registered plumber if you are not confident fitting the lagging yourself.

Taking the time to insulate your plumbing now will lower the risk of a severe leak when the weather turns cold. If you need help reaching awkward loft pipes or want a professional to handle the whole job, you can find a plumber near you to get a fixed price for the work.

Find a top rated plumber near you

4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county:

All counties and towns · The UK Top 100 plumbers

Alice Moore
Written by
Alice Moore Writer

Alice writes for Top Rated Plumbers, with a focus on helping homeowners compare quotes and ask the right questions. Away from the desk, she runs a book club with friends.

Looking for a trusted plumber? Browse our verified listings.

Find a Plumber