The central heating pump pushes hot water round your radiators. A failing pump typically shows as cold radiators while the boiler still fires. Typical 2026 price lists put a full replacement at £150 to £400, which includes the new pump and the fitting. If you are unsure of the issue, or the repair seems too complex, call a heating engineer rather than trying anything yourself.
What does a central heating pump do
The central heating pump is a small electric motor that acts as the heart of your heating system. It circulates heated water through the pipes. The pump pushes hot water from the boiler to your radiators or your hot water cylinder, and then pulls the cooler water back to the boiler to be reheated.
Without a working pump, the boiler can heat the water, but that heat has no way to travel around your home. Depending on the heating system, the pump may sit inside the boiler or elsewhere on the pipework. This matters for repairs. Where the pump sits inside a boiler, the work is for a Gas Safe registered engineer only. You must not remove the boiler casing yourself to inspect or change an internal pump.
Signs your central heating pump is failing
A failing pump struggles to move water efficiently, which creates obvious temperature drops in the home. You will usually notice the problem at the radiators first. Common signs of a failing central heating pump include:
- Cold radiators and no hot water across the house
- Uneven heating where some areas of the property stay cold while others get too hot
- The boiler taking much longer to heat up the house than it used to
- Cold spots on individual radiators
- The boiler running normally but no heat reaching the radiators, while the hot water still works
- Gurgling, grinding or whooshing noises coming from the pump unit
- Excessive pump vibration that you can feel through the surrounding pipes
- Leaks around the pump body or the pipe connections
A pump that shows any of these signs needs an engineer to look at it.
Is it the pump or something else
Many pump symptoms look exactly like other heating faults. You might have no heating or hot water because the pump has broken, but similar symptoms come from air in the system, heavy sludge, or low system pressure. A faulty thermostat, timer, or set of smart controls might simply be failing to send the signal for the pump to start.
A tripped fuse or a blown circuit breaker will stop a pump immediately, making it seem broken when it just lacks power. A seized pump is also common after the heating has sat unused over the summer. Because these issues overlap so heavily, a heating engineer must diagnose the exact fault. The causes listed for a pump that is not working also include corrosion, loose connections, blockages from debris and a broken pump, so there are several things to rule out before the pump is named as the problem. If the hot water still works while the radiators stay cold, tell the engineer, because that pattern is one of the signs listed for a failing pump.
You should only take safe user level actions. Check that your heating is switched on at the wall. Check that your programmer is calling for heat. If the boiler shows a low pressure warning, follow the manufacturer's instructions. If the settings are correct and the radiators stay cold, call an engineer.
Do not attempt to bleed the pump yourself. Do not try to free a seized pump manually. Do not drain the heating system, and never open the boiler casing or touch any internal electrics.
What causes a central heating pump to fail
Pumps operate under constant heat, pressure, and water flow. Several different issues can cause them to break down or stop working. An engineer will check for the following common causes. A stopped pump is not always a broken pump, because a tripped fuse or blown circuit breaker can stop it.
Electrical faults are often named as the most common cause of a pump not working. These include a tripped fuse, a blown circuit breaker, a wiring problem, or a failed capacitor inside the pump itself. Without a steady electrical current, the motor cannot turn.
Corrosion damages the metal casing and internal workings over time. Loose connections can also interrupt the power supply. Blockages can come from debris or from sludge, which builds up from rust and debris in the system.
Air in the system can create an airlock. Seizing is a mechanical failure where the internal parts lock together tightly. This is particularly common after long periods of summer inactivity.
General wear and tear eventually breaks down the moving parts inside the pump. A faulty thermostat or control box can also cause the pump to behave erratically. Finally, low system pressure deprives the pump of the water volume it needs to operate correctly.
Repair or replace the pump
When the engineer finds the fault, they will weigh up a repair against a full replacement. A seized pump can sometimes be freed temporarily by the engineer, but older pumps that seize usually need replacing soon after.
Leaks around the pump often mean a replacement is needed. This is especially true if the leak comes from a corroded housing, so replacement is often needed. Grinding or whining noises suggest worn bearings and a pump nearing the end of its life.
Age is a major factor in the decision. Most pumps last about 10 to 15 years, so it helps to tell the engineer how old your pump is. If a pump is over 10 years old and keeps failing, replacement is usually more cost-effective than paying for repeated repairs and call-out fees.
How much does a central heating pump replacement cost
Prices for a central heating pump replacement depend on the type of pump, the complexity of the plumbing, and the rates in your area. Quotes will be higher in London and the South East. When you ask an engineer for a price, check whether VAT and the cost of the physical pump are included in the figure.
Estimates vary. Some 2026 price lists give the figures in the first table, with the pump and installation fees included in the replacement price.
|
Type of work |
Estimated price range |
|---|---|
|
Minor pump repair |
£100 to £200 |
|
Full pump replacement, pump and installation |
£150 to £400 |
Others give different figures, shown in the second table, with labour included in the total.
|
Type of work |
Estimated price range |
|---|---|
|
Full pump replacement, unit and installation |
£150 to £350 |
|
Power flush for sludge, a separate job |
£350 to £800 |
Both sets of figures are estimates, so ask each engineer for a written fixed price. Local quotes will differ based on the engineer you choose and how easily they can access your pump. A quote is a fixed price for the job, whereas an estimate can change if the work takes longer than expected.
If the engineer finds sludge, a power flush is a separate job and the charge depends on property size and system condition. Read more about the power flush cost.
How long does a pump last and what shortens its life
Most central heating pumps last about 10 to 15 years. Sludge, hard water, missed servicing, low pressure and long periods of non-use can all shorten that life.
The Health and Safety Executive strongly advises that gas appliances and flues are checked for safety at least once every 12 months, so keeping up with an annual service also covers the missed servicing that can shorten a pump's life.
A pump is also more likely to seize after the heating has sat unused for months over the summer, so it is worth asking an engineer to look at the system before the cold weather.
What an engineer does when they replace a pump
In general terms, an engineer isolates the electricity and water supplies, checks the pump and its connections to confirm the fault, replaces the unit, refills the system and tests the heating. This is not a job to copy at home.
Because the pump may sit inside the boiler casing, the Health and Safety Executive states that anyone working on gas appliances in domestic premises must be a Gas Safe registered engineer and competent in that area of gas work.
An engineer's competencies are marked on the back of their Gas Safe Register ID card, which you should ask to see. To check an engineer, use the Gas Safe Register's Find an Engineer or Check an Engineer service, or call 0800 408 5500. The Health and Safety Executive also strongly advises that gas appliances and/or flues are regularly checked for safety at least once every 12 months.
Common questions
Why is my central heating pump noisy?
Gurgling, grinding or whooshing noises are listed among the signs of a failing pump, and grinding or whining suggests worn bearings. Do not try to bleed or free the pump yourself. Ask an engineer to inspect it.
Can a boiler run if the pump is broken?
Yes, a failing pump can show up as the boiler running but no heat reaching the radiators, while hot water still works. A broken pump still needs an engineer to diagnose it.
Is a boiler pump replacement a DIY job?
No. Replacing a central heating pump involves electrics and water, and it is not a job for you to do. If the pump is inside the boiler, the work must be done by a Gas Safe registered engineer.
Does my system need a new pump or just a clean?
This depends on what the engineer finds. A seized pump can be freed temporarily but older pumps usually need replacing, and leaks, a corroded housing or worn bearings often mean replacement. Sludge may need a power flush as a separate job.
What to do next
If your radiators are cold, your boiler is slow to heat up, or your pump is making unusual noises, take these steps to narrow down the problem safely:
- Check that your heating is switched on at the main programmer.
- Ensure your room thermostat is turned up and calling for heat.
- If the boiler shows a low pressure warning, follow the manufacturer's instructions.
- Tell the engineer if the heating stopped suddenly, as electrical faults are a common cause.
- Call a qualified heating engineer to diagnose the exact fault, especially if you are unsure of the issue, the repair seems too complex or you want to avoid further damage.
- Get quotes from several providers, including at least two from Gas Safe registered engineers.
- Do not attempt to open the boiler casing or loosen any pump connections yourself.
If you suspect a gas leak or a spilling appliance at any point, call the gas emergency number 0800 111 999, open doors and windows, and shut off the gas at the meter control valve. Otherwise, you can find a professional to diagnose your heating system and quote for a repair. You can find a plumber near you today.
Find a top rated plumber near you
4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county: