Replacing a tired, rusty or undersized radiator is a common job. A like for like swap onto existing pipework is usually a one to two hour job. Labour is commonly put at about £70 to £150 per radiator in some 2026 estimates and £150 to £300 in others, with London and the South East higher, and the radiator itself is extra.
A like for like swap means the tradesperson hangs the new radiator on the existing wall brackets and connects it to the existing pipes. This is the simplest way to swap a radiator. If you want the tradesperson to supply the radiator and fit it, the final bill will depend on the style of radiator you choose.
The table below shows typical all in prices for a mid range radiator including labour and VAT.
|
Radiator type |
Rest of UK |
London and South East |
|---|---|---|
|
Single panel |
£120 to £240 |
£150 to £300 |
|
Double panel |
£160 to £320 |
£200 to £400 |
|
Towel |
£150 to £300 |
£180 to £360 |
|
Column |
£200 to £500 |
£250 to £600 |
|
Designer |
£250 to £700+ |
£300 to £800+ |
These are typical 2026 prices and local quotes will differ. You can expect jobs in London and the South East to run roughly 15 to 30 per cent higher than the rest of the UK.
Radiator prices by type
If you prefer to buy the radiator yourself, the tradesperson will only charge you for their labour. The type you choose makes a big difference to the upfront cost. On these figures panel radiators start cheapest, while cast iron, designer and stainless steel models can cost significantly more.
The table below shows typical supply prices for different styles of radiator, excluding fitting.
|
Radiator type |
Typical supply price |
|---|---|
|
Panel |
£20 to £120 |
|
Column |
£115 to £380 |
|
Designer |
£180 to £500 |
|
Vertical |
£100 to £575 |
|
Towel |
£25 to £500 |
|
Cast iron |
£120 to £750 |
|
Flat panel |
£150 to £300 |
|
Stainless steel |
£175 to £580 |
These are typical 2026 prices and local quotes will differ. The supply prices were worked out differently from the all in prices above, so read them separately. As a rough guide to dimensions, a small radiator is about 40cm high by 60cm wide. A medium radiator is about 60cm high by 100cm wide. A large radiator is about 80cm high by 180cm wide. These are only examples of sizes, as the true measure of a radiator is its heat output.
Average replacement jobs run at about £150 in total for a small radiator. A medium radiator averages £200, and a large replacement averages £250.
Valves, drain down and other extras
When you ask a tradesperson to price a like for like swap, you need to know exactly what is covered. A standard quote usually includes a specific set of tasks to get the new unit safely onto the wall and working.
A standard replacement normally includes:
- Isolating or draining the system as needed
- Removing and disposing of the old radiator
- Hanging the new radiator on the existing brackets and pipework
- Refilling the system and bleeding the air out
- Testing the new radiator and valves for leaks
However, many homes need extra work to get their heating running efficiently. If your old radiator was cold at the bottom, your pipes may be full of rust and debris. In this case, you might need a power flush, which is a deep clean that pumps chemicals through the pipes to clear out sludge. You might also want to upgrade your controls.
The following items are usually charged separately:
- The radiator itself if the plumber supplies it
- New manual valves or thermostatic radiator valves
- New pipework for a repositioned or upsized radiator
- Draining and rebalancing the whole heating system
- A power flush to remove sludge from the pipes
- Making good any damaged decoration or flooring
Fitted thermostatic radiator valves, which sense the room air temperature and adjust the flow of hot water automatically, cost £70 to £140 per radiator. A full power flush cost is around £400. If you just need the heating system balanced, which means adjusting the valves so hot water flows evenly to every room, this costs £100 to £200.
If you are redecorating and simply want a radiator permanently removed, a removal only job costs £80 to £120. Old radiator disposal is usually an extra £20 to £50 if it is charged separately.
Adding a radiator or moving one
If you want to move a radiator to a different wall, or add a completely new one to a cold room, the job becomes much larger. The tradesperson cannot simply use the existing connections and will need new pipework.
Because this takes more time and materials, it costs more than a simple swap. An additional radiator needing new pipework costs £150 to £250 with a small business, or £200 to £350 with a larger national company.
You will also need to factor in the cost of making good. Making good any damaged decoration is usually charged separately, so ask who will do it and what it will cost.
How long the work takes
A simple like for like swap typically takes one to two hours to complete. If the tradesperson can easily turn off the valves and isolate the single radiator, the job is very fast. Hourly rates for this kind of work run from £45 to £75, varying heavily by region.
If you are repositioning a radiator, upsizing to a much larger model, or asking for whole system work, the job can take half a day or more. Draining down an entire house takes time, though the drain down labour is shared across a full house replacement, lowering the per radiator cost.
Keep in mind that plumbers usually charge a minimum fee, often with a call-out fee that covers the first hour. If you ask a plumber to come out on an evening, a weekend or a bank holiday because a radiator is leaking badly, this will carry a premium rate.
What size radiator do you need
Radiators should ideally be sized to the room's heat loss. Heat loss is the amount of heat a room loses through its walls, windows and roof. Many people simply measure the gap on the wall and buy a radiator to fit the old pipework. This is a common mistake.
Heat loss depends on several factors in your home. You should ask your installer to calculate this for you, or use a reliable manufacturer calculator online. Do not rely on simple formulas based only on the square metres of the floor.
The heat loss of a room depends on:
- The physical size of the room including the ceiling height
- The type and thickness of insulation in the walls and loft
- Whether the windows are single or double glazed
- The number of outside walls exposed to the cold weather
Once you know the heat loss, you can choose a radiator with the right output. Radiator outputs are measured in watts or British Thermal Units per hour. One watt is equal to 3.412 BTU an hour. Radiator outputs are usually given in one or both of these units.
Why output depends on water temperature
When you read the output on a radiator box, that figure is not guaranteed for every home. Radiator outputs are declared at a standard temperature difference called delta T 50 under a rule known as BS EN 442. Delta T is the average water temperature inside the radiator minus the room air temperature.
A delta T of 50 degrees Celsius is a standard test condition, so the output on the box is not guaranteed for every home.
Crucially, a radiator gives less heat at lower water temperatures. A conversion table gives a multiplier of 0.51 for going from delta T 50 to delta T 30. This means that at a delta T of 30, a radiator puts out roughly half the heat it does at delta T 50.
Heat pumps and lower flow temperatures
This temperature difference matters deeply if you are moving to modern heating methods. Heat pumps and low temperature systems are designed to run much cooler than older gas or oil boilers. Because the water inside the pipes is not as hot, the radiators may need to be larger.
If you are planning to change your heating source, ask the installer whether your radiators would need to be larger. You can read more about what this involves in our air source heat pump cost guide. A heating engineer can tell you exactly how large the radiators need to be for a lower flow temperature.
Do not change your boiler's flow temperature settings without following the manufacturer's instructions. Ask the installer if you are unsure.
Getting an accurate quote
When you are ready to hire, it is vital to get a proper written quote. A quote is a fixed price for the job. An estimate is just a guess and can change once the work begins. Ask the tradesperson to confirm in writing whether VAT, parts, materials and waste disposal are included in the total price.
Under the Consumer Rights Act 2015, any service you pay for must be carried out with reasonable care and skill. If a tradesperson leaves your new radiator leaking or poorly fitted, you have the right to ask for the poor work to be put right at no extra cost. Services arranged by phone, online or at your home usually carry a 14-day cooling-off period, giving you the right to cancel. However, this does not automatically apply to urgent repairs you have specifically asked for.
Replacing a radiator may be a plumber's job or a heating engineer's. There is no legal licence required for general water plumbing in the UK. WaterSafe is the national register of approved plumbers, and its members are trained in the strict Water Fittings Regulations. However, if the job requires work on the gas boiler itself, by law only Gas Safe registered engineers may carry this out. Draining and refilling a system safely should be left to a professional, and you can read more about this in our radiators not heating up and balancing guide.
Common questions
Do I need a plumber or a heating engineer to change a radiator?
Many plumbers are also heating engineers, but not all plumbers are registered to work on gas. A plumber can drain your system, swap a radiator and refill it. However, if the job requires opening the boiler casing or adjusting gas components, you must use a Gas Safe registered engineer.
How much does it cost to just cap off a radiator?
If you are decorating and want a radiator permanently taken away, the tradesperson will remove it and cap off the pipework. A removal only job costs £80 to £120. Getting rid of the old unit usually costs an extra £20 to £50 for disposal.
Do you have to drain the whole system to change one radiator?
Some swaps can be done by isolating the radiator, while others need part of the system draining. This is a job for the plumber, so ask which applies to yours. Draining down labour is shared across a full house replacement, which lowers the per radiator cost.
What does delta T 50 mean when buying a radiator?
Delta T is the average water temperature inside the radiator minus the room air temperature. Under a standard called BS EN 442, radiator outputs are declared at a delta T of 50 degrees Celsius. If your system runs at a lower water temperature, the radiator will put out less heat.
What to do next
If your radiator is leaking, turn the heating off and catch the water in a shallow container. If water is near electrics and it is safe to reach, switch off the electricity at the mains. Once the immediate area is safe, follow these steps to get the problem fixed.
- Turn the heating off and catch the water if you have an active leak
- Ask a local plumber to calculate the exact heat loss for your room
- Decide if you want to upgrade to thermostatic radiator valves at the same time
- Request a written quote that clearly includes parts, labour and waste disposal
- Ask the plumber how long the job will take and if they need to drain the system
When you are ready to get fixed prices for your home, you can find a plumber near you to assess your pipework and recommend the right size radiator for your room.
Find a top rated plumber near you
4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county: