Cost Guides

Air Source Heat Pump Cost and the Boiler Upgrade Scheme Grant

What an air source heat pump costs to install in 2026, how the £7,500 Boiler Upgrade Scheme grant works, what affects the price and what to check before you commit.

Illustration of an air source heat pump outside a brick house

The median cost of an air source heat pump installed under the government's Boiler Upgrade Scheme was about £12,500 in 2024/25. If you live in England or Wales and are replacing fossil fuel heating such as gas, oil, LPG or electric, you can usually get a £7,500 grant through the scheme to bring this price down. The government now officially calls these air to water heat pumps, but this guide uses the familiar name.

How much does an air source heat pump cost?

The final bill for fitting a heat pump depends heavily on the size of your property and the amount of pipework that needs changing. A typical installation costs between £9,500 and £18,000 before any government grants are applied. On average, it is £9,000 more expensive to install a heat pump than to simply replace an existing fossil fuel heating system without using the grant. To put this into perspective, the average new boiler cost in the UK including VAT is estimated at about £3,500, which highlights why the government grant is so important for homeowners.

Installation costs for heat pumps supported by the government scheme have fallen by 11 per cent since the scheme began in 2022. This drop in price makes the technology more accessible, but it remains a major investment for any homeowner. The total price you are quoted will reflect the heat pump unit itself, the labour required to fit it, and any upgrades your home needs to make the system work efficiently.

An air source heat pump works differently to a traditional boiler. It sits outside your property, taking heat from the outside air and transferring it to the water that circulates through your radiators and hot water cylinder. Because the system runs at a lower temperature than a gas or oil boiler, the installation often involves more than just swapping the main heating unit.

Upgrading your central heating is a major project that involves lifting floorboards, altering pipework and wiring in new controls. It is not a job that can be rushed, and the price reflects the skilled labour required across several days.

Typical prices by home size

The table below shows typical published prices for fully installed air source heat pumps in 2026 based on the size of the property.

Property size

Typical fully installed cost

Estimated installation time

2-bed semi-detached

About £10,500

2 to 3 days

3-bed semi-detached

About £13,000

3 days

4-bed detached

About £15,000

3 to 4 days

5-bed detached

About £17,000

3 to 4 days

These figures are typical published prices for 2026, and local quotes will differ based on your specific property.

Prices in London and the South East are generally higher due to increased labour and operating costs. The time it takes to fit the system is longer than a standard boiler swap. A two to four day installation means you will be without central heating for a short period. A good heating engineer will explain how they plan to manage this disruption, especially if the work is taking place during the colder months. They will usually drain your old system, remove the redundant boiler, fit the new outdoor unit and carefully flush the existing pipework before connecting the new components.

When you ask for a price, make sure the engineer gives you a written quote rather than an estimate. A quote is a fixed price that cannot be changed unless you agree to extra work in writing. An estimate is only a rough guess and can increase significantly once the job begins. You should also check that the total includes VAT, all parts, materials and the safe disposal of your old boiler and any water tanks.

How the Boiler Upgrade Scheme grant works

The Boiler Upgrade Scheme is a government initiative designed to help property owners cover the upfront cost of switching to low carbon heating. It provides fixed grant amounts that are deducted directly from your installation bill.

The current funding available through the scheme includes:

  • £7,500 towards an air source heat pump
  • £7,500 towards a ground source heat pump
  • £5,000 towards a biomass boiler
  • £2,500 towards an air to air heat pump

If you live in an off gas area, there is extra help available. Until March 2027, an additional £1,500 is available towards an air source or ground source heat pump if the property uses oil or LPG heating and has no mains gas.

The grant process is designed to be straightforward for the customer. You do not apply for the money yourself. Instead, you contact an installer who is certified by the Microgeneration Certification Scheme, commonly known as MCS. Once you agree a quote, the installer applies for the grant on your behalf on the Ofgem website.

The value of the grant is taken off the amount you pay and must be shown clearly as a deduction on your quotation and your final invoice. Ofgem will contact you directly to confirm that the installer is acting for you. They may also phone you or visit your home to check the installation, and the MCS body may carry out their own checks to ensure the work meets strict industry standards.

Who can get the grant

The Boiler Upgrade Scheme is open to people in England and Wales. If you live in Scotland, you may be able to get an interest free loan or a grant to make your home more energy efficient through a separate scheme. The Boiler Replacement Scheme in Northern Ireland is now closed.

To check if you are eligible for the grant in England and Wales, you must meet a few clear rules. First, you must own the property. This applies whether it is your own home, a building used for a business, a second home, or a property you rent out to tenants.

You must also be replacing a fossil fuel heating system, such as oil, gas, electric or LPG. The scheme is designed to replace older, carbon heavy systems, so it does not fund the replacement of an existing low carbon heating system. It also does not fund hybrid systems, which combine a gas boiler with an air source heat pump.

There are a few property types that are excluded from the scheme:

  • Most new build properties
  • Social housing
  • Properties that have already received government funding for a heat pump or a biomass boiler

If you have previously had funding for insulation, this does not stop you from applying. Timing is also important to remember. The installer must commission and install the heat pump within 120 days of applying for the grant. This prevents applications from sitting idle and ensures the funding goes to projects that are ready to proceed.

What else might need upgrading

Because heat pumps operate at a lower flow temperature than traditional boilers, your existing pipes and radiators may not be able to heat your home effectively without some changes. A responsible heating engineer will survey your property and tell you exactly what needs upgrading before they give you a final price.

If your radiators are too small, they will not release enough heat into the room. Upgrading to larger radiators or models with more panels usually costs about £150 to £300 per radiator. Your installer might also recommend fitting new radiator valves to give you better control over the temperature in individual rooms.

You will also need a way to store hot water. If you currently have a combi boiler, which heats water on demand and has no storage tanks, you will need to have a hot water cylinder fitted. A new hot water cylinder costs between £800 and £1,500 supplied and fitted. You will need to find space in your home for this cylinder, such as an airing cupboard or a utility room. The installer will also fit a magnetic filter to catch debris and protect the new system from sludge.

Electrical upgrades are another common extra. A heat pump requires a dedicated electrical circuit to handle the power load safely. This work is usually quoted separately by an electrician. Electricians typically charge about £45 to £80 an hour, or £250 to £500 a day. Depending on the age of your home, you might also need your consumer unit, which is your main fuse box, updated to meet current safety regulations.

What a heat pump costs to run

Many homeowners switch to a heat pump hoping to reduce their monthly outgoings. Between 90 per cent and 95 per cent of property owners surveyed were satisfied with their heat pump, and owners most commonly reported lower energy bills after installation.

The table below outlines the estimated annual running costs for an air source heat pump based on the size of the property.

Property size

Estimated annual running cost

2-bed house

£700 to £1,000

3-bed house

£800 to £1,200

4-bed house

£1,000 to £1,400

5-bed house

£1,200 to £1,500

These are published estimates for 2026, not quotes, and your own costs will differ.

Running costs depend heavily on how well insulated your home is, the specific energy tariff you use, and how well the heating engineer has designed the system. Heat pumps run on electricity, which generally costs more per unit than mains gas. However, a well designed heat pump produces more heat than the electricity it uses.

To keep running costs low, your home needs to hold onto the heat it generates. Draughty windows, uninsulated lofts and empty cavity walls will force the heat pump to work harder, pushing your electricity bills up. You should also factor in the cost of an annual service, which usually costs between £100 and £200. An annual service is often a condition of the manufacturer warranty.

Do you need planning permission?

In many cases, fitting an air source heat pump is classed as permitted development, meaning you do not need to submit a full planning application. However, there are strict limits to this, and the rules depend on where you live and the type of property you own.

For houses in England, the outdoor unit and its housing must not exceed 1.5 cubic metres in volume. If you live in a semi-detached or terraced house, only the first heat pump unit is covered by permitted development rights. A detached house is allowed to have up to two units without a planning application.

The position of the unit is also regulated. Units placed on pitched roofs are not permitted development. If you want to place the unit on a flat roof, all parts of it must be at least one metre away from the edge of the roof.

In November 2024, the government announced that the rule requiring a heat pump to be installed at least one metre from a property boundary would be removed in England from early 2025. This change was designed to help more households install a heat pump without the cost and delay of a planning application.

If you live in a conservation area, the unit must not be installed on a wall or roof that faces a highway. If you live in a listed building, permitted development rights do not apply within the grounds at all. You will always need planning permission and listed building consent. If you live in Wales, in a conservation area, in a listed building or in a flat, you should check the exact rules with your local council before any work begins.

All installations done under permitted development must comply with the MCS planning standard, known as MCS 020, which ensures the unit does not create too much noise for your neighbours. In England, installing any new or replacement heating system is notifiable under Building Regulations. If your installer is registered with a competent person scheme, they will notify the local authority for you and issue a certificate of compliance. If they are not, you must submit a building notice or full plans application yourself and pay a fee for a council inspection.

Choosing an MCS certified installer

To access the Boiler Upgrade Scheme grant, your chosen installer must be certified by the Microgeneration Certification Scheme. This scheme ensures that the company has the right training and follows strict industry standards for low carbon heating.

Because water plumbing in the UK does not require a legal licence, checking an installer's credentials is the best way to protect yourself. WaterSafe is the national register of approved plumbers, with approved contractor schemes run by bodies such as APHC and CIPHE, and its members are trained in the Water Fittings Regulations. If you are unsure where to start, reading up on what to check before you hire a local plumber can help you spot the warning signs of a bad tradesperson.

Under the Consumer Rights Act 2015, any service you pay for must be carried out with reasonable care and skill. If the work is poor, you have the right to ask the installer to put it right at no extra cost. Services arranged online or at home usually carry a 14-day cooling-off period, giving you time to change your mind, though this does not automatically apply to urgent emergency repairs you have requested. If you run into problems, Citizens Advice can offer guidance on your rights.

When comparing installers, never choose on price alone. A very cheap quote might mean the installer is cutting corners on system design or using lower quality materials. Ask at least three certified companies to visit your home and provide a written quote. A proper quote should list the exact make and model of the heat pump, detail any radiator upgrades, and explain the warranty terms. Avoid companies that demand large cash payments up front without providing any official paperwork, and be wary of call handling firms that pass jobs on to subcontractors at inflated rates.

Is a heat pump right for your home?

Deciding whether to move away from a traditional boiler is a big step. A heat pump offers a modern, efficient way to heat your property, but it requires the right environment to work well.

First, consider the space outside. The external unit needs a good flow of air around it to extract heat efficiently, so it cannot be boxed in tightly or placed in a narrow alleyway. You also need to think about the space inside. If you are moving from a combi boiler, you will need room for a new hot water cylinder, for example in an airing cupboard.

The most important factor is the thermal efficiency of your home. A heat pump provides a steady, lower level of heat throughout the day, rather than the rapid blasts of high heat you get from a gas boiler. If your home loses heat quickly through poorly insulated walls or an uninsulated roof, the system will struggle to keep you warm and your electricity bills will rise.

If you are unsure, a good heating engineer will give you an honest assessment. They should measure your rooms, check your radiators and calculate the heat loss of your home before recommending a system. If they try to pressure you into a quick sale without doing these checks, look for a different installer.

Common questions

How much does a heat pump service cost?

An annual service for an air source heat pump typically costs between £100 and £200. Regular servicing keeps the system running efficiently and is usually required to keep your manufacturer warranty valid.

Can I keep my gas boiler and add a heat pump?

Systems that combine a traditional gas boiler with a heat pump are known as hybrid systems. While these are available, they are not funded by the Boiler Upgrade Scheme, so you cannot get the £7,500 grant if you choose this option.

Does having cavity wall insulation stop me getting the grant?

No, having had previous government funding for insulation does not stop you from applying for the Boiler Upgrade Scheme. The only funding exclusions relate to previous grants for heat pumps or biomass boilers.

Will I need a new hot water cylinder?

If you currently have a combi boiler, you will need a hot water cylinder fitted as part of the installation because combi boilers do not have any internal water storage. This usually costs between £800 and £1,500 supplied and fitted, and you will need enough space inside your home to house it.

Do I have to apply for the grant myself?

No, the application process is handled by your installer. Once you agree to a quote from an MCS certified installer, they will apply to Ofgem on your behalf, and the grant amount will be deducted directly from your final invoice.

What to do next

Moving to an air source heat pump takes careful planning. Before you commit to an installation, take the following steps to ensure you get a reliable system and a fair price:

  • Check your home's insulation and draught proofing to make sure a heat pump will be efficient.
  • Look for installers who are registered with the Microgeneration Certification Scheme so you can claim the grant.
  • Ask three different companies to survey your home and provide detailed, fixed price written quotes.
  • Check that the quote clearly shows the £7,500 grant deduction and says whether VAT, materials and electrical work are included.
  • Confirm whether your existing radiators need upgrading and ensure this cost is included in the final price.
  • Ask the installer to explain how long you will be without heating and how they will manage the disruption.
  • Check the planning rules with your local council if you live in Wales, in a listed building, in a conservation area or in a flat.

Taking the time to compare quotes and check qualifications will help you avoid poor workmanship and unexpected costs. When you are ready to start gathering prices, you can find a plumber near you to discuss your options and arrange a thorough property survey.

Find a top rated plumber near you

4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county:

All counties and towns · The UK Top 100 plumbers

Alice Moore
Written by
Alice Moore Writer

Alice writes for Top Rated Plumbers, with a focus on helping homeowners compare quotes and ask the right questions. Away from the desk, she runs a book club with friends.

Looking for a trusted plumber? Browse our verified listings.

Find a Plumber