Fitting an outside tap typically costs between £100 and £300 in 2026 for a completely new installation. A plumber takes a branch from your internal cold water pipe, passes it through the external wall and fits the new tap on the outside masonry. The job is a straightforward plumbing task that makes watering the garden or washing the car much easier. The installation must include a double check valve to meet the water fittings rules and protect the drinking water supply. This guide explains what the installation involves, how the rules protect your drinking water and how to prepare your garden tap for winter so it does not freeze and burst.
How much does fitting an outside tap cost?
The price of your installation depends on whether you are fitting a brand new tap or replacing an old one. A new installation requires the plumber to cut into your internal pipework, drill a hole through the exterior wall and run new copper or plastic pipe. Replacing an existing tap is much quicker because the pipework and the hole through the brickwork are already in place.
Plumbers charge for these jobs in different ways. Straightforward jobs are usually quoted as a fixed price, which gives you certainty before the work begins. If the route for the new pipe is complicated, the plumber might charge by the hour. Typical hourly rates for a plumber are £40 to £70, while day rates range from £250 to £400. If you need someone urgently because an old tap has burst, emergency call-out fees range from £60 to £120.
The table below shows typical prices for fitting a new outside tap and the labour for replacing an existing one.
|
Type of work |
Typical price |
|---|---|
|
New outside tap installation |
£100 to £300 |
|
Garden tap replacement labour, rest of the UK |
£50 to £100 |
|
Garden tap replacement labour, London and the South East |
£75 to £150 |
These figures are typical published prices for 2026, and your local quotes will differ based on the exact job and your location.
You should ask for at least three quotes in writing before you hire someone to do the work. A proper written quote must show the cost of labour, materials, waste disposal and any call-out fee. You should also check whether the final price includes VAT and ask the plumber for clear timescales for the installation.
What the job involves
Fitting a new outside tap starts inside your home. The plumber will locate your cold mains supply pipe, which is often found under the kitchen sink or near the internal stop tap. They will turn off your water at the mains so they can cut into the pipes safely without causing a flood.
The plumber takes a branch off this cold water pipe to feed the new outdoor tap. They fit an isolating valve on this new section of indoor pipe. This small valve allows you to turn the water supply to the outside tap on and off from inside the house, which is essential for winter maintenance and carrying out future repairs.
Next, the plumber drills a hole through your external masonry wall. They pass the new water pipe through this hole to the outside. The outside tap is then screwed securely to the brickwork so it does not move when you attach a hosepipe.
Once the tap is fixed in place, the plumber turns the main water supply back on. They test the new pipework and the tap to make sure there are no leaks. They will also show you how to operate the internal isolating valve before they finish the job.
The double check valve and why it is required
The most important part of fitting an outside tap is stopping contaminated water flowing backwards into your clean drinking water. This backward flow is known as backflow. It can happen if there is a sudden drop in pressure in the main water network, which sucks water back down the pipes.
The Water Supply (Water Fittings) Regulations are legal rules designed to keep drinking water safe. They specify that outside taps should always have a double check valve installed to prevent backflow. If stagnant water in a hosepipe is drawn back into your home, it can bring soil, garden chemicals and harmful bacteria with it. Bacteria such as Legionella thrive in warm, stagnant water left sitting in a garden hose.
Homes built since 1999 typically have an inline double check valve built into the supply pipe leading to the outside tap. Homes built before 1999 usually have the check valve built into the tap itself.
These valves do not last forever and can fail over time. The British Standard BS EN 806-5 states that check valves should be replaced every ten years. You can read more about these rules in the WaterSafe guide to double check valves. If you are unsure whether your current tap has a working valve, ask a qualified plumber to test it.
Where the tap and pipe can go
Outside taps are often fitted to the back wall of the house, close to the kitchen sink. This keeps the new pipework short and makes the installation cheaper. If you want the tap at the far end of your garden or next to a detached garage, the pipe will need to be laid underground.
Laying underground water pipes is subject to strict rules to prevent the water freezing in winter and to protect the pipes from accidental damage. In England and Wales, the Water Supply (Water Fittings) Regulations 1999 require you to give notice to your water company before work starts on certain underground pipes.
This notice is required for any water system laid outside a building that is less than 750mm below ground level, or more than 1350mm below ground level. Pipes laid shallower than 750mm are more at risk of freezing, and pipes laid deeper than 1350mm are harder to reach for repairs.
You must not begin the installation without the water company giving their consent, though they cannot withhold this consent unreasonably. Once you submit your notice, the water company must respond within ten working days. If they do not reply within that time, consent is treated as given and the work can begin. You can read the exact legal wording in regulation 5 of the Water Supply (Water Fittings) Regulations 1999.
Garden watering systems and notifying the water company
The rules for notifying your water company also depend on how you plan to water your garden. A standard hosepipe that you turn on and off by hand does not require any special permission. You simply attach it to a compliant outside tap and use it as needed.
Automated garden watering systems are treated differently by the regulations. Because they are permanently connected to the water supply and operate without a person present, they carry a much higher risk of unnoticed leaks and backflow contamination.
If you plan to install a garden watering system that is not designed to be operated by hand, you must give notice to your water company before work begins. The same ten working day response period applies to this notice. Your plumber can advise you on the specific backflow prevention devices an automated irrigation system will need.
Using a hosepipe safely
Even with a double check valve installed on your tap, you must use your hosepipe safely to protect your drinking water. Warm water left in a hose is a perfect breeding ground for bacteria, and poor watering habits can force dirty water back into the mains supply.
The national register of approved plumbers offers clear guidance on safe hosepipe use. You should follow these practical rules every time you water the garden or wash the car.
- Keep a gap between the end of the hose and any water so it is never submerged.
- Do not put hosepipes in drains, garden ponds, buckets or watering cans.
- Fit a self-closing control such as a trigger spray gun to use less water and reduce the risk of backflow.
- Keep the hose somewhere cool and out of direct sunlight when you are not using it.
- Run the hose without attachments until the water runs cool before you use it.
- Turn the hose off at the tap when you are finished.
- Disconnect the hose and store it clean and dry when it is not in use.
Following these steps reduces the risk of contaminated water being siphoned back into the drinking water supply. You can find more practical tips in the WaterSafe weather hacks guide.
Protecting an outside tap in winter
Frost is a common cause of damage to outside taps. When temperatures drop below freezing, the water left inside unprotected taps and pipes turns to ice. Water expands as it freezes, and this can make taps and pipes crack and burst, with the leak often showing only once the ice thaws.
You must prepare your outside tap before the first winter frost arrives to prevent this damage.
- Isolate the outside water supply by turning off the internal isolating valve on the pipe that feeds the tap.
- Drain the outside tap by leaving it open so any remaining water has room to expand safely if it freezes.
- Disconnect the hosepipe and put it away to stop it freezing and reduce the risk of backflow.
- Fit an inexpensive insulating tap cover over the metal tap body.
- Put foam lagging on any exposed pipes in unheated areas.
- Fix dripping taps, inside and out, to save water and prevent frozen water backing up.
A WaterSafe approved plumber can help you find your outdoor shut-off valves if you cannot locate them. You can read more about dealing with plumbing leaks in our guide on how to detect a water leak.
Replacing a leaking or old outside tap
Outside taps endure harsh weather and frequent use, so they eventually wear out. If your tap drips constantly, a worn part can often be replaced, but an old, corroded or damaged tap is usually better replaced. Check valves should be replaced every ten years, so an older tap with a built-in check valve may no longer protect your drinking water.
A like-for-like installation typically takes 30 minutes to an hour to complete. The plumber will turn off the water, unscrew the old tap from the wall plate and fit the new one. The job will take longer if the existing pipework is heavily corroded and needs replacing.
The typical price for a leaking tap repair ranges from £60 to £120. A standard garden tap replacement costs £50 to £100 in labour for most of the UK, or £75 to £150 in London and the South East. If the tap only drips, a repair may be enough, and the guide on fixing a dripping tap explains the usual causes. If you replace it, ask the plumber to confirm that a double check valve is fitted, either in the tap or on the pipe.
Choosing a plumber for the job
There is no legal licence required for general water plumbing in the UK. This means anyone can call themselves a plumber, which is why checking a tradesperson's qualifications and approved schemes matters.
WaterSafe is a free online directory and national accreditation body for competent and qualified plumbers. Its approved plumbers belong to recognised contractor schemes run by APHC, CIPHE, SNIPEF and WIAPS. These approved members are trained in the Water Fittings Regulations and should hold a recognised qualification.
An approved contractor can issue a Certificate of Compliance when they finish your tap installation. This certificate shows that the work meets legal requirements.
You are also protected by the Consumer Rights Act 2015 when you hire a plumber. This law states that a service must be carried out with reasonable care and skill. If the plumber does a poor job, you can ask for the work to be put right at no extra cost. Services arranged by phone, online or at home usually carry a 14-day cooling-off period. This period does not automatically apply to urgent repairs you have asked for. If you have a dispute with a tradesperson, you can contact Citizens Advice for guidance.
Common questions
Who is responsible for the outside water pipe?
Your local water company is responsible for the water main and the pipe up to your property boundary. As the property owner, you are responsible for the supply pipe on your land and all the plumbing inside the building. If a leak happens on your side of the boundary, you must hire a plumber to fix it.
Do I need an outside tap cover?
An outside tap cover is highly recommended during the winter months to prevent frost damage. It is an inexpensive insulating jacket that wraps around the metal tap to stop the water inside from freezing. Frozen water expands and can crack the tap body, leading to severe leaks when the ice melts.
What is a double check valve outside tap?
A double check valve is a safety device that allows water to flow in only one direction. It stops dirty water from a garden hosepipe flowing backwards into your clean drinking water. Homes built before 1999 usually have this valve built directly into the tap, while newer homes have it fitted inline on the pipework inside the house.
How long does fitting an outside tap take?
Replacing an existing outside tap with a new one typically takes 30 minutes to an hour. Fitting a brand new tap from scratch takes longer because the plumber must alter your internal pipes and drill a hole through the exterior wall.
Next steps
Before you hire a tradesperson to fit your new tap, make sure you have the right information ready.
- Decide where you want the tap to go and whether the pipe will need to run underground.
- Check if you need to notify your water company about a new automated garden watering system.
- Ask plumbers if they are trained in the Water Fittings Regulations and belong to an approved scheme.
- Get at least three written quotes that show the cost of labour, materials and VAT.
- Ask the plumber to confirm that a compliant double check valve is included in the installation price.
Once you are ready to start gathering quotes, you can use our directory to find a plumber near you.
Find a top rated plumber near you
4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county: