Modern boilers have built-in sensors that constantly monitor how the system is running. When these sensors detect that something is wrong, they trigger a safety shutdown to prevent damage to the boiler or danger to your home. The display screen will then flash a sequence of letters and numbers to help explain what has happened.
This sequence is the fault code, which is sometimes called an error code. It gives you a starting point for working out whether you have a simple issue you can resolve safely yourself, or a mechanical failure that requires a professional. The code might point to a lack of water, a blocked pipe, or an internal part that has stopped working entirely.
Fault codes do not always pinpoint the exact broken component. They tell you the general area where the boiler failed its sequence of safety checks. A heating engineer uses this code alongside their own physical tests to find the root cause of the breakdown.
There is no universal system for boiler error codes in the UK. Every manufacturer decides how to program their own display screens. This means the same code can mean something different on another make, which is why the manual for your own boiler is the reference.
If you search online for a code without knowing the make of your boiler, you will often find conflicting answers. This confusion can lead you to check the wrong thing. You must always match the code to the specific make and model of your boiler.
Never assume a code means the same thing on your current boiler as it did on your last one.
What F1 can mean
On one make of boiler, an F1 code means there is not enough water in the system. This is a low pressure fault that stops the boiler from firing up.
When a boiler detects low water pressure, it shuts down to protect its internal parts from overheating. If you have this specific make of boiler, the F1 code is telling you that the pressure has dropped below the minimum required level. Check the pressure gauge and read the manufacturer's instructions for what to do about low pressure.
However, you cannot assume F1 means low pressure on every boiler. Other makes use their own codes, so the same code may not mean low pressure on your boiler. Always check your own manual before you act.
If your manual confirms that F1 means low pressure, you can look at the gauge on the front of the boiler or underneath it and follow the manufacturer's instructions. You can learn more in our guide on what pressure should a boiler be.
Other common faults the codes point to
The table below shows some types of fault a code can point to and gives examples of how the specific codes differ from one manufacturer to another.
|
Fault type |
What the boiler is doing |
Examples of codes on different makes |
|---|---|---|
|
Low pressure |
Not enough water in the system |
F1 on one make |
|
Ignition failure |
Boiler fails to light the gas |
F28, E133, L2, LF, or EA |
|
Pump or fan failure |
Internal parts are not working |
F75, F32, E160, E125, F3, A1, or C6 |
|
Frozen condensate pipe |
Waste water is blocked by ice |
E133 on one make |
Note that these codes differ by manufacturer. The table shows examples of how one fault can trigger completely different codes depending on the make of your boiler, and how a single code can sometimes mean more than one thing.
For example, one make uses the exact same E133 code for both an ignition failure and a frozen condensate pipe. This is why reading the code is only the first step in understanding the problem, and why the manufacturer instructions are essential.
Safe checks before you call anyone
When your boiler shows a fault code, there are several safe actions you can take before paying for a call-out. These basic checks can sometimes clear the fault and get your heating back on immediately.
You can safely carry out these steps yourself:
- Write down the exact fault code and note what the boiler was doing when it appeared.
- Check the pressure gauge to see if the needle has dropped below the normal working range.
- Confirm the boiler has power by checking the display screen and the main switches.
- Check your gas supply is active by making sure the bill is paid or the prepayment meter has credit.
- Thaw an easily reached frozen condensate pipe outside with warm water.
- Follow the manufacturer instructions in your manual to reset the boiler once.
If the pressure is low, follow the manufacturer's instructions. If the weather has been freezing, a frozen condensate pipe can shut a boiler down. You can find safe steps for clearing the ice in our guide to a frozen condensate pipe.
If you have checked the pressure and the gas supply, you can press the reset button. Sometimes a boiler just needs to restart its safety sequence after a minor interruption. You can read more about doing this correctly in our guide on how to reset your boiler.
Why you must not open the boiler
It is very tempting to try and fix a boiler yourself when you are cold and want to avoid repair bills. However, taking the cover off a boiler is dangerous and illegal for anyone who is not qualified. Only a Gas Safe registered engineer should open it.
By law, only Gas Safe registered engineers are allowed to open the boiler casing or do any internal repairs. Never try to fix a gas fault yourself, and never attempt an electrical repair inside the unit. It is dangerous, and Which? says it can invalidate your boiler warranty.
Safety warning: Carbon monoxide is a poisonous gas that you cannot see, smell or taste. If you suspect an appliance is leaking carbon monoxide, you must call the Gas Emergency Freephone on 0800 111 999. You must also switch off the appliance, open your doors and windows to ventilate the property, and see your GP immediately.
The Health and Safety Executive warns that symptoms of carbon monoxide poisoning include headaches, dizziness, breathlessness, nausea, tiredness, and pains in the chest or stomach. Never ignore these signs, and always leave the internal boiler checks to a registered professional.
When a fault code needs a Gas Safe engineer
While you can thaw an easily reached outside pipe, many faults need professional help. You will need to hire a Gas Safe registered engineer if the code indicates an internal failure.
Professional help is essential for repeated flame or ignition failures, and for any fan or pump errors. If you have attempted to reset your boiler 3 times and it is still not working, you have a fault with your boiler and should contact a Gas Safe registered engineer. Try the reset once following the manual, and stop if the fault comes back.
Do not ignore faults, as they can become more serious the longer you leave them. The table below shows what you can expect to pay a heating engineer to investigate and fix a boiler fault.
|
Type of heating engineer service |
Typical cost range |
|---|---|
|
Simple re-pressurising by an engineer |
£80 to £150 |
|
Diagnostic visit |
£70 to £90 |
|
Weekday call-out |
£60 to £120 |
|
Emergency or out-of-hours call-out |
£100 to £200 or more |
|
Full range of boiler repairs |
£150 to £700 or more |
The figures above are typical published 2026 estimates based on homeowner quotes. Local quotes will differ depending on your area, the exact fault, and whether parts and materials are included. An average repair usually lands between £300 and £350, but the final bill will depend on exactly what the fault code has found.
Under the Consumer Rights Act 2015, any repair service must be carried out with reasonable care and skill. If an engineer fixes the boiler but leaves it leaking water, you can ask for the poor work to be put right at no extra cost. Services arranged by phone or online usually carry a 14-day cooling-off period, but this does not automatically apply to urgent repairs you have specifically asked the engineer to carry out. You can find more general guidance on your consumer rights by visiting Citizens Advice.
What to tell the engineer when you ring
When you call a heating engineer, they will ask you for details about the breakdown. Giving them clear and accurate information helps them bring the right parts and gives you a better chance of getting the boiler fixed on the first visit.
Have this information ready before you pick up the phone:
- The exact make and model of your boiler.
- The specific fault code flashing on the display screen.
- When the problem started and what the boiler was doing at the time.
- Whether you have hot water, central heating, or neither.
- Any safe actions you have already tried, such as resetting it or checking the pressure.
A good engineer will use these details to give you an idea of their call-out fee and their hourly rate. Remember that small jobs and repairs are usually charged by the hour, often with a call-out fee that covers the first hour of work. Evenings, weekends and bank holidays carry a premium rate.
Always ask if the price they give you over the phone is a quote or an estimate. A quote is a fixed price for the work, whereas an estimate is just a rough guess that can go up once they start the job. Before they arrive, check their Gas Safe registration card to ensure they are qualified to work on your specific type of boiler.
How to find your boiler's own codes
The only way to be certain what a fault code means is to read the manufacturer instructions that came with your boiler. The manual will explain the fault codes and let you know if you can fix the problem yourself safely.
If you have moved into a new house or lost the original paperwork, you can still find this information easily. Most manufacturers have an online copy available to download on their websites. You will need to know the make and model.
Once you have the manual, look for the fault code section and follow the specific advice given for that exact model. If the manual tells you to contact an installer or a service engineer, you must follow that instruction and arrange a repair.
Common questions
Can I clear a boiler fault code myself?
You can clear some fault codes yourself if they relate to safe, external issues. If the manual says the code means a frozen condensate pipe, you can thaw an easily reached pipe with warm water. If it means low pressure, follow the manufacturer's instructions. After that you can reset the boiler once, following the manual.
Why does my boiler keep locking out?
A code is the boiler's way of saying a fault or safety shutdown has happened. If your boiler keeps locking out after you reset it, there is a fault that needs a Gas Safe registered engineer.
Are boiler error codes the same for all brands?
No, boiler error codes are not the same across different brands. Every manufacturer programs their own display screens, meaning the same code can mean different things on different makes. You must always check the manual for your specific make and model to understand what the code means.
How many times can I reset my boiler?
Reset your boiler once, following the manual, after checking the pressure and the gas supply. If you have attempted to reset it three times and it is still not working, you have a fault and should contact a Gas Safe registered engineer.
Next steps
When your boiler displays a fault code, staying calm and following the right sequence of checks will save you time and money. Use this short checklist to decide what to do next.
- Write down the code and find the manual for your specific make and model online or in your paperwork.
- Check the pressure gauge and follow the manufacturer's instructions if the pressure looks wrong.
- Confirm that your gas supply is working and that the boiler has electrical power.
- Look outside to see if the plastic condensate pipe has frozen in cold weather.
- Call a Gas Safe registered engineer if the manual states the code requires a professional repair.
If your checks show that the boiler has suffered an internal failure, or if it refuses to start after a single reset, it is time to call in a professional. You can use our directory to find a plumber near you who is registered to work on gas and can diagnose the fault safely.
Find a top rated plumber near you
4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county: