Maintenance

Magnetic Boiler Filters and Whether Your System Needs One

What a magnetic boiler filter does, what it costs fitted in 2026, whether your system needs one, how it relates to warranty and the annual service, and when sludge needs more than a filter.

Illustration of a filter housing on a pipe next to a boiler with a jar of dark sludge

A magnetic boiler filter is a device fitted on the heating pipework near your boiler that catches rust sludge with a large magnet. It is not mandatory, but it can help prevent expensive blockages in your central heating system. As an extra on a boiler job it typically adds 120 to 225 pounds. Retrofitting one to an existing system typically costs about 180 to 260 pounds all in. These are 2025 and 2026 prices and depend on access.

What a magnetic boiler filter is

Water flowing through your central heating system reacts with metal radiators and pipes over time. Over time this reaction creates sludge, which is mostly made up of rust particles from corroded pipes and radiators. As the central heating pump pushes water around your house, it carries this heavy debris with it.

A magnetic filter sits on the pipework and pulls these rust particles out of the water using a large, strong magnet. The water passes through the filter, the magnet grabs the metallic debris, and the cleaner water continues into the boiler.

While the main job is catching rust, some models also catch non-magnetic deposits from corroded copper, zinc or aluminium parts.

What sludge does to a heating system

As sludge builds up, it can cause several problems:

  • It can block the boiler heat exchanger, and a blocked boiler often overheats and shuts down.
  • It can block the central heating pump.
  • It can block radiators.

Modern pipework is often narrower than older plumbing. This narrower design makes blockages more likely.

When sludge blocks the heat exchanger, the boiler cannot transfer heat away from the burner fast enough. The boiler often overheats and shuts down to protect itself. Clearing a severe blockage is difficult and disruptive work. It may require a full power flush or a heat exchanger replacement, which Which? describes as costly. A filter is meant to help prevent blockages, though it cannot clear one that is already there.

Do you need a magnetic filter?

A magnetic filter is not a legal requirement, and you are not breaking any rules if you choose not to have one installed. A good installer should raise the topic of cleaning, flushing and whether system filters or scale reducers are needed before they start work.

A filter works alongside a chemical corrosion inhibitor, not instead of one. The chemical inhibitor alters the water to stop the rust forming inside the steel radiators in the first place. The filter then catches any particles that do manage to break loose. Using both is more effective than either alone.

If you are having a new heating appliance fitted, there are specific rules for preparing the system. The Building Regulations guidance for England states that before a new heating appliance is installed, all central heating and primary hot water circuits should be thoroughly cleaned and flushed out. The guidance also says a suitable chemical inhibitor should be added to the primary heating circuit to protect against scale and corrosion. You can read this guidance in Approved Document L Volume 1.

What a magnetic filter costs

The price of a magnetic filter depends heavily on when you choose to have it installed. Fitting one as an extra on a boiler job is typically cheaper than retrofitting one, because the engineer is already working on the system. Retrofitting can cost more.

This table keeps the two kinds of figure separate.

Installation type

Typical cost range

Added as an extra on a new boiler job

120 to 225 pounds

Retrofitted to an existing system

180 to 260 pounds

The extra on a boiler job is a 2026 figure and the retrofit range is a 2025 figure, so read the two separately, and local quotes will differ. For a retrofit the total can be around 200 pounds all in, made up of up to 100 pounds for the filter, up to 20 pounds for the inhibitor and up to 100 pounds for labour.

Retrofit prices can also run higher, at roughly 245 to 260 pounds including labour. The final price you pay will vary depending on how easy the filter is to get to and whether the engineer supplies the unit or you buy it yourself.

Filters and boiler warranties

Some boiler manufacturers extend the boiler warranty if a magnetic filter is installed. Check the terms of your own boiler's warranty to see whether yours does, and what evidence of water treatment it asks for before you agree to any work.

You must also check the warranty terms regarding chemical treatments. Some manufacturers require evidence of the correct inhibitor dose to keep the warranty valid. Keep the paperwork, because a warranty can depend on it. Always ask your installer for paperwork detailing the water treatment they carried out.

Where it goes and when it does not fit

A magnetic filter is fitted on the heating pipework close to the boiler, so that it catches debris before it reaches the boiler.

The unit itself is bulky and is fitted close to the boiler. Because of its size, a filter is not always practical for every home. If your boiler is tucked inside a small kitchen cupboard or a tight airing space, there may not be enough room on the pipework to accommodate the device.

Your heating engineer will need to inspect the pipework and tell you if a filter will fit.

Cleaning the filter and the annual service

A magnetic filter does not clean itself or dissolve the sludge it catches. As it pulls rust and debris out of the water, the filter fills with what it catches, which is why it needs to be cleaned.

Heating engineers usually clean the filter during an annual boiler service. Ask your engineer to do this at the service. A filter does not replace the corrosion inhibitor, so it is also worth asking them to confirm the inhibitor side of the water treatment is in order, and to note both on the service paperwork.

This cleaning ensures the filter is ready to protect your boiler for another year. You can learn more about what happens during a boiler service to understand how engineers maintain your system. Do not attempt to open or clean the filter yourself. It is very easy to cause a leak, damage the watertight seals, or drop the system pressure if you do not know how to isolate the unit properly.

A filter is not a power flush

If your central heating system is already full of sludge, adding a magnetic filter alone will not fix the problem. The filter is designed to catch small amounts of debris slowly over time. It is a preventative measure for a relatively healthy system, not a cure for a heavily blocked network of pipes.

If your radiators are cold at the bottom or your boiler is already kettling and making banging noises, a heavily sludged system may need a power flush before a filter is fitted, so ask your engineer to advise.

A power flush is typically 400 to 850 pounds as an extra on a boiler job. Once the system is completely clean, the engineer adds fresh inhibitor and fits the magnetic filter to keep it that way. You can read our power flush cost guide to understand exactly what the job involves and when it is necessary.

Questions to ask your engineer

When you are getting quotes for a boiler replacement or a system upgrade, you need to know exactly what is included in the final price. Some installers include a magnetic filter, a chemical flush and a new dose of inhibitor as standard. Others quote a lower baseline price and list these protections as optional extras.

To avoid surprises on the final bill, ask your heating engineer these questions before you agree to the work:

  • Is a magnetic filter included in this quote, or is it an extra cost?
  • Do you supply the filter, or do I need to buy it myself?
  • Will the filter fit in the space around my boiler, or is my cupboard too small?
  • Are you doing a chemical flush or a full power flush before fitting the new boiler?
  • Will you add a corrosion inhibitor once the system is refilled?
  • Does fitting this specific filter extend the boiler warranty with the manufacturer?
  • Will you provide paperwork showing the system was flushed and treated?

Getting these answers in writing ensures you can compare quotes fairly. It also proves exactly what you have paid for. For more advice on dealing with installers and comparing prices, read our guide on questions to ask before you accept a boiler quote.

Common questions

Can a magnetic filter stop my boiler shutting down?

If your boiler is shutting down because sludge has blocked the heat exchanger, a filter can help prevent it happening again in the future. However, if the blockage is already there, the system will need to be cleaned or flushed out first. A filter protects a clean system from future build up, but it cannot reverse existing damage or clear a blocked pipe on its own.

Do I still need corrosion inhibitor if I have a filter?

Yes, you still need a chemical inhibitor in the water. A filter works alongside a corrosion inhibitor, not instead of one. The chemical stops the rust forming inside the radiators in the first place, while the filter catches any particles that do manage to break loose.

Can I fit a magnetic filter myself?

You should not attempt to fit a magnetic filter yourself. It involves cutting into the central heating pipework, draining part of the system, and ensuring watertight seals on pressurised pipes. A qualified heating engineer will ensure it is fitted safely without causing leaks, water damage, or sudden pressure drops in the boiler.

How often should the filter be emptied?

Heating engineers usually clean the filter during the annual boiler service, so ask yours to include it. Do not try to open or clean it yourself.

Next steps for your heating system

If you are planning to have a filter fitted, or if you are gathering quotes for a new boiler, follow this checklist to get things right:

  • Check your current boiler warranty documents to see if a filter or a specific inhibitor dose is required.
  • Ask your heating engineer to check if there is enough space on the pipework near the boiler.
  • Get a written quote that clearly states whether the filter, the labour and the chemical inhibitor are included.
  • Ask the engineer if your system needs a power flush before the filter is installed.
  • Keep the final paperwork to prove the system was treated with inhibitor, in case you need to claim on the warranty later.

A magnetic filter is a practical way to protect your boiler from costly breakdowns, provided your system is clean to begin with. If you are ready to get quotes for the work or need an engineer to check your pipework, you can find a plumber near you to assess your system and explain your options.

Find a top rated plumber near you

4,869 plumbers across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county:

All counties and towns · The UK Top 100 plumbers

Alice Moore
Written by
Alice Moore Writer

Alice writes for Top Rated Plumbers, with a focus on helping homeowners compare quotes and ask the right questions. Away from the desk, she runs a book club with friends.

Looking for a trusted plumber? Browse our verified listings.

Find a Plumber